How to measure your threshold

You need a ruler or tape measure with millimeter or 1/16 inch marks, a straightedge (a level or a stiff ruler works) and your phone camera. Millimeters are best. Write down what you actually measure and don't subtract any clearance yourself.

Side view of a doorway threshold with the threshold height, the floor space in front of it and the gap under the door marked H D G Lower floor Threshold Door
H threshold heightD open floor in frontG smallest gap under the door where the ramp sits
  1. Threshold height (H)Stand the ruler upright on the lower finished floor and measure straight up to the top of the threshold. Check the left, center and right, and send all three readings if they differ.
  2. Doorway width (W)Measure the clear opening between the inside faces of the door jambs, where the ramp will sit. Send the real opening without taking anything off.
  3. Edge shapeLook at the front edge of the threshold at floor level and note whether it's square, angled or rounded (see below).
  4. Floor space (D) and door clearance (G)Measure the open floor in front of the threshold, from its base into the room. The ramp reaches about 3.4 times the threshold height into the room, so a 1 in threshold needs roughly 3.4 in of open floor. Note which way the door swings and the smallest gap under the door or door sweep along that path.
  5. Robot and sidesWrite down your robot vacuum's brand and model. If you need a ramp on both sides of the doorway, measure each side on its own and label them Side A and Side B.
Top view of a doorway: the width is measured between the inside faces of the door jambs, with a ramp on Side A and an optional ramp on Side B Side A Side B, if needed W Room A Room B Wall Wall
Top view. W runs between the inside faces of the jambs. One ramp set covers one side, so a doorway that needs both sides gets a Side A and a Side B, each measured on its own.

Square, angled or rounded edge

The front edge decides how the ramp meets the threshold, so check it closely. Then send a close side-on photo at floor level with a ruler next to it, plus a photo of the whole doorway from above.

H
Square. Measure straight up from the lower floor to the top of the threshold.
H depth
Angled. Rest a straightedge flat on the threshold and measure from the floor to its underside. Add the slope's horizontal depth if you can measure it.
H
Rounded. Measure to the underside of a straightedge, like an angled edge. Rounded or irregular edges may need extra measurements or a traced profile before the fit is confirmed.

Size options and prices

Each price is for one complete ramp set for one side of a doorway, with standard shipping within the US included.

Price by threshold height and doorway width
Threshold heightUp to 32 in wideOver 32 to 48 in wide
Up to 0.6 inup to 15.24 mm$39.99$54.99
Over 0.6 to 0.9 inover 15.24 to 22.86 mm$49.99$64.99
Over 0.9 to 1.2 inover 22.86 to 30.48 mm$59.99$79.99
Over 1.2 to 1.6 inover 30.48 to 40.64 mm$74.99$94.99

A measurement right on a line belongs to the lower range: exactly 0.9 in goes in Over 0.6 to 0.9 in. Doorways over 32 in (812.8 mm), up to 48 in (1219.2 mm), use the wider option.

What to send in your Etsy message

Send this through Etsy Messages before you order. Copy it, fill in your numbers and attach the photos.

Hi! Here are my measurements for a robot vacuum ramp.

Units (mm or inches):
Threshold height, left / center / right:
Doorway width between the jambs:
Edge shape (square, angled or rounded):
Slope depth, if angled:
Open floor in front of the threshold:
Door swing direction:
Smallest gap under the door or sweep:
Robot vacuum brand and model:
Sides needed (Side A, or Side A and Side B):

Photos attached: side-on at floor level with a ruler, and the whole doorway from above.

Photos to attach:

  • A close side-on photo at floor level, with a ruler standing next to the threshold.
  • The whole doorway from above.
  • If the door passes over where the ramp will sit, a photo of that too.

How ordering works

  1. MeasureFollow the steps above and take the photos.
  2. Message me on EtsySend your measurements, photos and robot model through Etsy Messages.
  3. Order your sizeOnce the fit and size are confirmed, choose your threshold height range, doorway width and color.
  4. Made to orderYour ramp is printed to your measurements and ships within 3 business days of purchase.

What you get

  • One ramp set for one side of a doorway, in segments that join with dovetail joints.
  • A shallow ramp designed around a 16 degree climb, with a thin 0.6 mm leading edge. Final dimensions depend on your threshold.
  • Double-sided mounting tape.
  • PLA for indoor doorways, with visible 3D-print layer lines.
  • Colors: Caramel, Dark Chocolate, Desert Tan, Latte Brown, Black, White, Bronze, Cyan and Red. Gray is planned but not available yet.

Good to know before you order

  • It's made for indoor robot vacuum use. It isn't a mobility ramp and isn't load rated.
  • Robots climb differently. Climbing ability, traction and clearance vary by model and threshold, which is why your robot's model is part of the order.
  • A custom ramp doesn't automatically mean every door will clear it, so check the gap under the door before ordering.
  • Keep PLA away from excessive heat and hot direct sunlight.

Questions

Do I need a ramp on both sides of the doorway?

One ramp set covers one side of a doorway. If you need both sides, measure each side separately, label them Side A and Side B, and send both so both size options can be confirmed.

My threshold is exactly 0.9 in. Which option do I pick?

Over 0.6 to 0.9 in. Each height range above 0.6 in leaves out its lower number and includes its upper one, so a measurement right on the line goes in the lower range.

My threshold is taller than 1.6 in. Can I get a ramp?

Not with the current size options, which stop at 1.6 in (40.64 mm). Send me your measurements and photos anyway, and I'll let you know if I can make one for your threshold.

How far does the ramp reach into the room?

About 3.4 times the threshold height, because it's designed around a 16 degree climb. A 1 in threshold needs roughly 3.4 in (86 mm) of open floor in front of it, and a 1.6 in threshold roughly 5.5 in (140 mm). Final dimensions depend on your threshold and are confirmed from your measurements.

Will it work with my Roborock, Roomba, Eufy, Dreame or Ecovacs?

Send your robot vacuum's brand and model with your measurements so I can check the fit. Climbing ability, traction and clearance vary by model and threshold. I'm not affiliated with these brands.

Will my door still close over the ramp?

Not automatically. Measure the smallest gap under the door or door sweep along its swing path, and send a photo if the door passes over where the ramp will sit, so clearance can be checked before you order.

Should I measure in inches or millimeters?

Millimeters if you can, or inches to the nearest 1/16. Send the actual measurements without subtracting any clearance.

How does the ramp stay in place?

It comes with double-sided mounting tape.

How long does it take to ship?

Each ramp is made to order and ships within 3 business days of purchase. Standard shipping within the US is included.

Can I return it?

Because each ramp is made to your measurements, change-of-mind returns aren't accepted. If it doesn't match the measurements you sent, or it arrives damaged, I'll reprint it or refund you. This doesn't limit Etsy's buyer protections.